CON'T FROM COMMENTS EARLIER. However, the installation took less than 3/4/ hour and was a basic regulator with no other function. Looking up the price afterwards, invoice did not list type or price, it appears that it would have cost me around $60 for the regulator and another $15 or so for the additional supplies necessary to install it and it was really a rather simple job with easy access. Given that, it seems that $300 for less that an hours worth of on site work, company says it does not include commute time in its prices, is a little high. While flat rate quotes are nice, they must take into consideration situations where the work load differs depending on the circumstances. Therefore, unless you are at the upper end of the harder work needed than the average job. it can be argued that my estimated price of $300 for labor was more than a little high. Maybe I am wrong since I have not used their services for years and am not knowledgeable of the costs of equipment and professional labor today.
Headquartered in Collin County Texas, Crown Plumbing Service is a family owned and operated corporation that remains committed to old fashioned values of professionalism, dependability and affordability. We realize that regardless of the magnitude of your repair, when you need plumbing service, urgency, accuracy, and integrity are critical to the success of your repair.
Got the plumbing service that I needed with SG1 Plumber. Our kitchen drain had been clogged from an incident with my son. The plumber, Lee, got to work immediately and did a really clean job on the pipes. He didn't even charge that much compared to other plumbing services that I tried before. They'll definitely get a call back from me if I ever experience a plumbing incident again.
Also known as a drain auger, a drain snake is a coiled device around ¼-inch thick. To use a drain snake, put the end into the entrance of the drain. Turn the handle to force the snake deeper, using extra pressure to force it through the bend in the pipe. Keep turning until the snake hits the clog, then either pull the snake and remove the obstruction or force it through. Once the snake is out of the drain, run the water on full blast for a few minutes to ensure the obstruction is completely removed.
Yesterday and today for the most part of my day's been frustrating I had 2 different plumbing companies who came in and they said it was not possible to do the repairs through the warranty company needless to say I requested one more time a different company this time that dispatched neighborhood plumber. I was contacted by Gary upon his arrival I realized this gentleman been at my house before. I explain the situation and then he said OK, for a while I did not hear him say anything about half hour later he came up to me, he stated that it was done. to my surprise he proved me that it was really done! I have to state this this guy he knows what he's doing. I wish the other 2 Companies would have witnessed him doing the job, when they told me it was impossible. On the note I would like to state my thankfulness to Gary from neighborhood Plumber. He is the best!
It was a bad experience with Mr. Rooter Plumbing of Las Vegas. Over the phone, I was quoted $79 to fix a clogged kitchen sink. The plumber was scheduled to arrive between 3-5pm so I took off work two hours early. Kenneth arrived at the door at 4:30pm and the price switched to $225 which was a total rip off. I told the plumber I was not happy but he didn't seem to care. He said "go ahead and write a bad review" so here it is. Needless to say I will never use nor recommend Mr. Rooter.
The cherry on top, is that throughout this whole experience Gary has asked for and used a TON of my household supplies. From the two towels (one of which you can see in the first picture) he used as drop cloths, the windex he used to not burn the wood with his torch, my wire hanger he bent to measure the space and all of the paper towels, tissues and toilet paper he wiped his hands with. I mean ALL of my other contractors brought their own supplies, how unprepared and unprofessional are these people??!!
Sometimes a faucet leak can be stopped by replacing the rubber washer at the end of a faucet stem or cartridge. This is a more common repair on older fixtures when things were built to last and designed to be able to be maintained. Other times the whole stem or cartridge needs replacement or the bibb seat deeper back into the fixture needs replacement. That leads to matching up the right components and often times making a trip to the hardware store or plumbing supply house necessary due to the many varieties, makes and models of faucets. My advice is to make sure your Plumber has faucet repair kit on their truck before having them come out to assess the issue.